[email protected]
13/1, om sakthi nagar, Pugalur(S.F) post, Karur. 639113

RESIN AND ACTIVATOR

WRAP SEAL PLUS RESIN AND ACTIVATOR

single-img-10

Features

  • Corrosion barrier and isolator
  • High adhesion strength
  • Excellent alkali and acid resistance
  • Ease of application by using paint rollers and paint brush
  • Applicable for pipes, tanks, and large surfaces

APPLICABLE MATERIAL:

  • Galvanized steel
  • Copper
  • Stainless steel
  • Carbon steel
  • Concrete
  • Polyethylene
  • FRP/GRE

CHEMICAL RESISTANCE:

  • MEK
  • Diesel
  • Ethylene glycol
  • Ammonia
  • Acetone
  • Crude oil
  • Toluene
  • Ethyl alcohol
  • Gasoline
  • Sodium hydroxide

WORKING TIME:

 10 minutes at 30 °C (86 °F)

CURING TIME:

 2 hours at 30 °C (86 °F)

APPLICATION:

  • Applied as corrosion coating on pipes, storage tanks, vessels, exhaust lines, bulkheads, machineries, joints, and large surfaces.
  • Applied with Wrap Seal PLUS Uncoated Fiberglass Tape, Chopped Strand Mat or Surface Tissue for reinforcement, bonding and lamination

APPLICABLE INDUSTRIES:

appli 1 - Resin and ActivatorBuilding & amp; Facilities
appli 2 - Resin and ActivatorElectronics
appli 3 - Resin and ActivatorIndustrial Processing
appli 4 - Resin and ActivatorIrrigation
appli 5 - Resin and ActivatorOil & amp; Gas
appli 6 - Resin and ActivatorChemical
appli 7 - Resin and ActivatorManufacturing Plants
appli 8 - Resin and ActivatorMarine
appli 9 - Resin and ActivatorMilitary
appli 10 - Resin and ActivatorOffshore
appli 11 - Resin and ActivatorFood Processing
appli 12 - Resin and ActivatorPetrochemical
appli 13 - Resin and ActivatorPharmaceutical
appli 14 - Resin and ActivatorPower Generation
appli 15 - Resin and ActivatorPulp & amp; Paper
appli 16 - Resin and ActivatorWastewater
appli 17 - Resin and ActivatorWater Distribution

TECHNICAL DATA:

Colour – Resin : Natural
– Activator : Straw colour
Viscosity : 20000 – 40000 cps at 21 °C (70 °F)
Specific gravity : 1.85
Compressive strength : 24500 psi (1723 kg/cm2)
Tensile strength : 35000 psi (2461 kg/cm2)
Bond strength : 500 psi (35 kg/cm2)
Flexural strength : 42000 psi (2953 kg/cm2)
Flexural modulus : 1.6×106 psi (112491 kg/cm2)
Barcol hardness : 40 – 50 Shore D
Coverage area (per set) : 0.15 m2 at 3 mm thickness

WRAP SEAL PLUS CORROSION REPAIR PROCEDURE:

1Procedure 1 - Resin and Activator
Corroded pipe surface
2procedure 002 - Resin and Activator
Roughen the area to be repaired
3Procedure 3 - Resin and Activator
Mix and stir Wrap Seal PLUS Resin and Activator for at least 1 minute until well mixed
4procedure 004 - Resin and Activator
Apply two coats of activated resin evenly over the area to be repaired and allow to cure
5aProcedure 5 - Resin and Activator
Immerse Wrap Seal PLUS Fiberglass Repair Tape into water
6aProcedure 6 - Resin and Activator
Wrap the fiberglass repair tape as tightly and evenly as possible, with at least 50% overlap over affected pipe length
7aProcedure 7 - Resin and Activator
Discard the plastic tube at the end of the roll
8aProcedure 81 - Resin and Activator
Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance
FLAT SURFACE/TANK
Procedure 9 - Resin and Activator
Apply Several layers of wrap Seal PLUS Surface Tissue or Wrap Seal Plus Chopped
Strand Mat onto the affected area.